User Manual - INCENSE LIGHT

To ensure safe use of this product, be sure to read this manual carefully before use.
Please keep this manual in a safe place for future reference/refer to it whenever necessary.
If improper use or any abnormality occurs, discontinue use immediately.

Country of origin: Japan Materials: Glass/Brass/Oleaceae Fraxinus wood Product dimensions: W85×D85×H70 (mm)

[How to assemble]

1. The brass tube for temporary fastening is pushed out from above with a pillar.
   
   

   The holes in the wooden base have thin brass tubes already inserted into them for temporary fastening.
   This is to prevent the hole diameter from changing slightly due to humidity, as natural wood is used.
   (This is to prevent the wood from shrinking and expanding, especially during storage and when humidity is high, making it difficult to insert the posts.)

   This tube can be removed by pushing it in from above using a brass post and then pushing it out from below.
   *It is difficult to remove with your fingers, so press the pillar straight in lightly.
   
   

2. Insert the brass pillar all the way in.
   
   Once the temporary fixing tube has been removed, insert the brass post straight into the hole in the base as far as it will go.
   Once the pillars are installed, you should generally continue using them as is without removing them.
   
   
   
3. Gently secure the glass disc with the screws
   
   

   The top of the post has a small screw that fits through a hole in the glass disc, then the glass disc is clamped to the post by lightly tightening the included screw from above.

   These screws are designed to fit the thickness of the glass disc, but if you tighten them too much, the glass may crack.
   Be sure to tighten gently until it stops lightly.

   
   

[How to use]

1. Light the incense, extinguish the flame, and let it burn so that smoke comes from the incense itself.
2. In a brass tube Insert the incense into the horizontal hole for the incense holder when it is burning and smoking. Please do not light the incense while it is set in the incense holder. A sudden change in temperature may cause excessive stress on the glass disc, which may result in breakage.
3. The glass disc disrupts the updrafts and creates beautiful incense cloud smoke patterns.

[Safety Precautions]

Ignoring these warnings may result in death or serious injury. ・Please make sure to read and understand the correct usage instructions before using the product.

・Please use incense within the length of the incense holder (8cm or less). Using incense in an unsuitable way may result in fire or other accidents.

・Do not use this product for any purpose other than its intended use.

・Please store/use out of reach of children and pets.

- Do not leave the incense unattended until it has completely burned out.

・The natural vegetable oils in the incense will discolor the surface of the product. This can be easily removed by wiping with alcohol.

- Friction may cause scratches on the product surface.

・Please be careful that there are no flammable objects in the vicinity.

- If you use a large amount in a small space, be sure to ventilate the area.

-Storing in a humid environment may cause deformation or mold.

・The temperature of the burning part reaches approximately 600 degrees. Please be careful not to get burned.

[Care instructions]

After using the incense several times, spray it with alcohol and wipe it off with a soft cloth.

-Since it is made of glass, it can be washed with a soft sponge and dishwashing detergent.

[Light specifications]

- Before use, remove the transparent sheet on the back of the unit.

- The light will flash slowly while charging and will turn off when charging is complete.

・USB cable is not included. You can use a commercially available USB cable (Type-C).

・The electricity cost for a single full charge is less than 0.1 yen.

Low light: Approx. 150 hours High light: Approx. 40 hours Flickering light: Approx. 70 hours

- The built-in battery can be recharged approximately 1,000 times. If you charge it once a week, the theoretical life span is about 20 years.

If the battery has enough power remaining, charging will not occur and the LED will flash twice.

- The light will automatically turn off 8 hours after the switch is operated.

-Since solid natural wood is used, there are individual differences in the grain and color.

-It is not waterproof, so do not place wet items on it.
- Do not use/store in water/humid locations or outdoors.

- When connecting the USB-C cable, please be careful not to press too hard as this may damage the USB connector.

・Do not modify or disassemble.

- Do not look directly at the lit LED for long periods of time as it may damage your eyes.